DMS load cell with measuring amplifier HX711AD

fig. 1: DMS load cell with measuring amplifier HX711AD

Autor:	Onyesi John Abiagam
Sprache:	DE EN

Introduction

A weighing scale is a measurement system used to determine the mass of an object by converting mechanical force into a readable value.

This system is based on a DMS load cell in combination with the HX711AD measuring amplifier. The applied force is converted into an electrical signal, which is processed and displayed as a weight value.

The signal is acquired using a microcontroller-based system and processed using Simulink. Calibration, signal filtering, stability detection, and tare functionality are implemented to ensure accurate and stable measurements.

Requirements

Table 1: Requirements for the Unit

Req.	Description	Priority
1	The mass must be determined using the HX711AD load cell via Arduino and Simulink.	1
2	The measuring range must be determined.	1
3	The measurement uncertainty (1σ) must be determined for the measuring range and displayed as a confidence interval.	2
4	The on/off button starts the system. The sensor must first be calibrated and display 0 g.	1
5	The weight must be referenced for the measuring range.	1
6	The measured values ​​must be filtered/smoothed over time.	1
7	A beep must indicate when the measured value is stable/constant.	1
8	The sensor system must display the weight in g on a display.	1
9	The tara button resets the current weight to 0 g (recalibration).	1

Working principle

This section explains how the DMS load cell and the HX711AD convert an applied force into a digital signal.

DMS Load Cell

Introduction

A DMS load cell converts mechanical force into an electrical signal. It consists of:

• a deformable metal body
• strain gauges attached to the surface
• resistance changes when stretched or compressed

Figure 1: Structure and deformation of a load cell. Source: https://learn.sparkfun.com/tutorials/getting-started-with-load-cells

Working Principle

When force is applied:

• the metal body deforms
• strain gauges change resistance
• gauges are wired in a Wheatstone bridge
• deformation → bridge becomes unbalanced
• output: small differential voltage

Figure 2: Wheatstone bridge configuration. Source: https://learn.sparkfun.com/tutorials/getting-started-with-load-cells

---

HX711AD Measuring Amplifier

Introduction

The HX711AD processes the small differential signal from the load cell. It includes:

• a programmable gain amplifier (PGA)
• a 24‑bit sigma‑delta ADC

Figure 3: HX711 module and pin configuration. Source: https://justdoelectronics.com/load-cell-hx711-module/

Working Principle

Signal processing steps:

• load cell outputs a millivolt‑level differential signal (A+, A−)
• PGA amplifies the signal
• 24‑bit ADC converts it to digital
• microcontroller reads data via:
  • DOUT (data)
  • SCK (clock)

Figure 4: Source: https://cdn.sparkfun.com/datasheets/Sensors/ForceFlex/hx711_english.pdf

Technical Overview

• The system consists of a DMS load cell, an HX711AD measuring amplifier, a microcontroller, an LCD, a buzzer, and two push buttons (power and tare).
• The load cell converts the applied force into an electrical signal, which is amplified and digitized by the HX711AD.
• The digital data is read and processed by the microcontroller.
• The measured weight is displayed on the LCD.
• A buzzer indicates when a stable measurement is reached.
• The power button controls the system state, and the tare button resets the measured value to 0 g.

Pin Assignment

3.1 Pin Assignment

This section describes the electrical connections between the load cell, the HX711AD,the buzzer,LCD and push buttons and the microcontroller.

Load Cell to HX711

Load Cell Wire	Function	HX711 Pin	Description
Red	Excitation + (E+)	E+	Supplies voltage to the bridge
Black	Excitation − (E−)	E−	Ground reference
White	Signal + (S+)	A+	Positive input signal
Green	Signal − (S−)	A−	Negative input signal
Yellow (optional)	Shield	GND	EMI protection

HX711 to Microcontroller

HX711 Pin	Function	Microcontroller Pin	Description
VCC	Power Supply	5V / 3.3V	Power input
GND	Ground	GND	Common reference
DOUT	Data Output	Digital Input	Sends measurement data
PD_SCK	Clock Input	Digital Output	Controls data read

Microcontroller Peripherals

Component	Function	Microcontroller Pin	Description
LCD	Display output	I2C (SDA/SCL)	Displays measured weight
Buzzer	Acoustic feedback	Digital Output	Indicates stable measurement
Push Button (Power)	System control	Interrupt Pin (e.g., D2)	Starts or stops the system
Push Button (Tare)	Reset function	Interrupt Pin (e.g., D3)	Resets measured value to 0 g

Related Links

• HX711 based weight scale

SVN-Repository

https://svn.hshl.de/svn/HSHL_Projekte/trunk/Arduino_Sensorsammlung

---

→ zurück zum Hauptartikel: HSHL-Mechatronik-Baukasten | Arduino Sensorsammlung | Sensorinbetriebnahme mit Arduino und Simulink